Stone walls made easy.....

The three Ts. Lift the lid on the secrets of how you do things so others can have a go.....
Post Reply
User avatar
dkightley
Posts: 1296
Joined: Wed Nov 13, 2013 9:43 pm
Location: Nottingham, UK

Stone walls made easy.....

Post by dkightley »

I thought I'd share the very easy method I have used to create stone walls......

I use the thin and low quality cardboard that you get as packaging for shirts produced in the far east. This card is shiny white one side and a stone gray fibrous finish on the other.

Cut a strip of width just over twice the height you want the wall to be. It doesn't matter if the width drifts...the wall will end up varying in height slightly! Unlike what I did...which shows in one of the photos below....if you mark the card for cutting, do it on the white side! Fortunately, most of the line you can see will be obstructed by undergrowth!

Now an important bit.....carefully hand crease the strip down its length and fold in half, crimping the fold just using finger and thumb. Don't be tempted to press the crease flat on a flat surface, or with a ruler, etc. You want the crease finish to be non-uniform! Apply a bit of glue inside the creased card and squeeze closed so you have what you can now see as a stone wall with an undulating top. Here's a couple of close-ups to illustrate what you should now have:
IMG_2668_red.JPG
On the left is the creased card; on the right it is glued down.

Once dry, the wall is ready to fix down on your layout. Using lots of pins, fix the wall into position, ensuring it sits down on the ground surface. Use pins inserted at an angle to hold it down, as you can see in the photo below.

Using a small paint brush, put a line of neat PVA glue along the bottom of both sides of the wall. Here's a close-up of where I got to on a couple of walls on The Bridge:
IMG_2653_red.JPG
Leave the PVA to dry overnight and then carefully pull the pins out. Here's the end product....a stone coloured stone wall:
IMG_2670_red.JPG
I've used a similar fixing technique for fixing wood panelled fencing, but use a single thickness of plain thin white card that has been pre-painted the right shade of brown.
You do not have the required permissions to view the files attached to this post.
Doug Kightley
Webmaster here and volunteer at the National Tramway Museum http://www.tramway.co.uk

User avatar
dkightley
Posts: 1296
Joined: Wed Nov 13, 2013 9:43 pm
Location: Nottingham, UK

Re: Stone walls made easy.....

Post by dkightley »

And just to finish off, here's the same spot once the shrubbery, etc has been applied:
IMG_2671_red.JPG
You do not have the required permissions to view the files attached to this post.
Doug Kightley
Webmaster here and volunteer at the National Tramway Museum http://www.tramway.co.uk

NeilM
Posts: 198
Joined: Thu Nov 14, 2013 9:46 am
Location: North Yorkshire, UK
Contact:

Re: Stone walls made easy.....

Post by NeilM »

That looks really effective, and so simply done.

A good reminder that details in T scale sometimes only need to be hinted at, rather than fully modelled to scale. I keep trying to work out how to model a dry stone wall in detail, and then realising that it would be no good trying to get that level of detail, even if it were possible.
Neil

T gauge items in my Shapeways shop http://www.shapeways.com/shops/t450

msimister
Posts: 98
Joined: Sun Jun 21, 2015 6:18 pm
Location: Melbourne, Australia

Re: Stone walls made easy.....

Post by msimister »

As an alternative to Doug's method above, I used glass paper, painted grey, folded in half and cut out. I didn't take Doug's advice to not make the fold 'hard'. Perhaps I should have done but I'm happy with the overall result. See pic below.

Cheers,
Malcolm
Dry stone wall from glass paper.jpg
Field enclosed by dry stone wall with semi-derelict barn.jpg
You do not have the required permissions to view the files attached to this post.

IanSmith
Posts: 1
Joined: Thu Oct 15, 2020 7:36 am

Re: Stone walls made easy.....

Post by IanSmith »

Doug and Malcolm

Thanks for both of your tips on modelling stone walls.

I have adapted this method over the past few weeks on my layout but using B&Q grey 120 grade paper. This saves painting (by and large) but can be painted green for hedges or brick red for walls.
For info: the landscaping I used foam board (thanks to Steve Twigg for this idea) for contouring sculpted to remove edges then glued kitchen roll for smoothing painted random grey/brown/white/black before scattering a mix of fine dark green turf with coarse rough pasture. The bushes are Woodland Scenics clumping material is very small lumps and the trees are the same material glued on to gauge.com tree skeletons. The buildings and from Shapeways.

This layout is nearing completion so I'm planning a new larger one (1.85m X .75m) using Flexi Track as the raised bed in this one (although robust and easy to use) is clunky.

So thanks again both.

King regards
Ian
You do not have the required permissions to view the files attached to this post.

Post Reply