Page 1 of 1
Posted: Wed Jan 25, 2017 5:57 pm
As the title says I'm new to T gauge so will be coming here with questions. I'd like to thank Martink for all the help he has given me so far.
Due to downsizing I'm moving from N to T. Will be ordering things in the next few days as soon as I have decided on which layout I'm going to use. Want to be sure to buy enough track
. One question I have now is about the PWM (the blue box), would a mobile phone charger ( 5V, 2.1A) work as a power supply?
Looking forward to the new gauge and learning more on this forum.
Posted: Wed Jan 25, 2017 8:12 pm
Welcome to t Gauge and to the Talking T Gauge forum.......
To answer you question......seeing as there's a commercial USB to PWM cable available then someone does not anticipate the power demand on the supply to be greater than 0.5A at 5v. (The spec for USB 2 has a max current specified at 0.5A, and 0.9A for USB3 ). And from my own experience, a power car motor consumes very little current. I've had a set of rechargeable batteries last several hour powering three power cars in one stint.
So....I would think that a power supply that is definitely 5v DC (not AC!!) with a current rating of 1.5A will be perfectly suited to powering a PWM.
And regarding your proposed layout....you are hereby instructed to start a thread in the Layout section giving full details of your plans.
Posted: Wed Jan 25, 2017 9:12 pm
It is 5 VDC but 2.1 A not 1.5 A so.......
Posted: Wed Jan 25, 2017 10:04 pm
chadnn wrote:It is 5 VDC but 2.1 A not 1.5 A so.......
That'll work - problems happen when it's underpowered.
Good luck. Make sure your track is absolutely even!!
Posted: Wed Jan 25, 2017 10:27 pm
Posted: Wed Jan 25, 2017 11:15 pm
Thanks for the help. Just don't want to burn anything up
Posted: Tue Jan 31, 2017 2:25 am
OK guys, will be receiving my trains within the next day or so and have another question, or two
Been reading where most of you glue your flex track down and some of you use double-sided tape. I'm going to use tape and wonder if you tape the whole track or just here and there? Also what do you use for ballast?
Posted: Tue Jan 31, 2017 1:47 pm
Well, I can answer the second half of your question, about ballast. The fine stuff sold by tgauge.com works quite well. I found the most useful tool to apply it was a paintbrush with a head about 8-10mm wide. Pour the ballast along the track, then run the brush down the track between the rails. The bristles touch the sleepers in the centre and on both sides and shape the ballast over the track nicely. You still have to do a bit of work to shape the edges, but it is all a lot easier than it sounds.
Posted: Tue Jan 31, 2017 5:17 pm
Unfortunately Tgauge is out of stock on the ballast so was hoping there was something else that could be used.
Posted: Thu Feb 09, 2017 7:03 am
Well found out you can't use a mobile phone charger on the blue pwm. Can still use the batteries but something burned inside and can't use the usb cord. Oh well
Posted: Thu Feb 09, 2017 10:41 am
Sounds like the charger unit you tried may not have been compatible after all. Was it 5 DC, as I said it needed to be? The polarity may possibly have been wrong. Did you check it with a meter before you plugged it in??
If it now is damaged and can only work on batteries, that should still be okay. Batteries will last a heck of a long time. I've used NiCad rechargeables for the best part of eight hours continuously powering two or more power cars at the same time without any problems. Duracells should last much longer before they need replacing.
Posted: Thu Feb 09, 2017 5:56 pm
It was a 5VDC, 2.1A charger. After it cooled down I tried a 5VDC, 1A charger and it seemed to be OK. So it seems that I had to many amps. Live and learn,just happy that I can still use it
Posted: Fri Feb 10, 2017 12:59 am
So it seems that I had to many amps.
It doesn't work like that. The amp values are the maximum current the power supply is designed to supply.....its capacity. The voltage is the killer in the equation. If the voltage was say 12v instead of 5v, then there is a risk that components will overheat spectacularly because 12v would generate a much higher current through the component than what 5v would. And if the power supply was AC instead of DC, then the danger is the reverse polarity half of the time. That would damage components as well!