•   
  • Talking T Gauge Shop
    Your online shop for T gauge locomotives, rolling stock and scenery items. Buy for your layout...and support the forum at the same time!

Board index Talking T Gauge Forum 3D Printing for T Gauge

Here's the place for discussions about those 3D creations for Tguage...and lets not forget the trials and tribulations of designing and printing.

Re: New products for the Talking T Gauge shop???

Postby dkightley » Fri Apr 07, 2017 11:56 pm

.....and now there's a Leyland Atlantean to compliment the Routemasters!
Doug Kightley
Webmaster here and volunteer at the National Tramway Museum http://www.tramway.co.uk
User avatar
dkightley
 
Posts: 861
Joined: Wed Nov 13, 2013 9:43 pm
Location: Nottingham, UK

Re: New products for the Talking T Gauge shop???

Postby gbtrains » Mon Apr 10, 2017 11:14 am

HI Doug

Thank you for drawing up the vehicles.

I have already placed my order.


regards
Graham :D
gbtrains
 
Posts: 108
Joined: Sat Jul 02, 2016 6:21 pm

Re: New products for the Talking T Gauge shop???

Postby gbtrains » Sun Apr 30, 2017 8:41 pm

Hi Doug
Do you have any ideas on making a forklift truck for the vehicle section if possible.

Regards
Graham
gbtrains
 
Posts: 108
Joined: Sat Jul 02, 2016 6:21 pm

Re: New products for the Talking T Gauge shop???

Postby dkightley » Fri May 12, 2017 11:29 pm

After having had cause to liaise with the emergency services on two separate occasions in the past few weeks, the next additions to the shop are a tribute to those heroic people who daily go above and beyond the call of duty to help those members of the public who need their assistance....
Only one gives a clue to what it is......
P1010986_red.JPG
P1010986_red.JPG (41.25 KiB) Viewed 630 times

On the left...a fire engine...and on the right....an ambulance.

Once I've managed to take decent photos, they'll both be in the shop...
Doug Kightley
Webmaster here and volunteer at the National Tramway Museum http://www.tramway.co.uk
User avatar
dkightley
 
Posts: 861
Joined: Wed Nov 13, 2013 9:43 pm
Location: Nottingham, UK

Re: New products for the Talking T Gauge shop???

Postby dkightley » Mon May 15, 2017 12:57 am

......and the said new products are now available.
Doug Kightley
Webmaster here and volunteer at the National Tramway Museum http://www.tramway.co.uk
User avatar
dkightley
 
Posts: 861
Joined: Wed Nov 13, 2013 9:43 pm
Location: Nottingham, UK

Re: New products for the Talking T Gauge shop???

Postby Nutter » Wed Jul 19, 2017 6:41 pm

With all these buses you have designed how about a Bus Station or Garage for them ;)
or a generic building that could also be a fire station.
Mike based on the Southern side of London

Posting most of the time from a mobile phone please excuse typos
Nutter
 
Posts: 330
Joined: Tue Feb 24, 2015 12:05 pm

Re: New products for the Talking T Gauge shop???

Postby dkightley » Thu Jul 20, 2017 4:28 pm

I woke up early EARLY this morning and couldn't get back to sleep......so I got up and looked for something "fun" to do!
P1020023_red.JPG
P1020023_red.JPG (60.21 KiB) Viewed 306 times

It's not fully finished.....but it has two doors front & two doors back that can be either lift-up sectional, or folding....depending which way round the door inserts are fitted. Or they can be left out to simulate the doors being open.

I've also started a similar building that is a small bus garage/depot....but I've not printed it yet!
Doug Kightley
Webmaster here and volunteer at the National Tramway Museum http://www.tramway.co.uk
User avatar
dkightley
 
Posts: 861
Joined: Wed Nov 13, 2013 9:43 pm
Location: Nottingham, UK

Re: New products for the Talking T Gauge shop???

Postby Nutter » Thu Jul 20, 2017 5:21 pm

dkightley wrote:I woke up early EARLY this morning and couldn't get back to sleep......so I got up and looked for something "fun" to do!
P1020023_red.JPG

It's not fully finished.....but it has two doors front & two doors back that can be either lift-up sectional, or folding....depending which way round the door inserts are fitted. Or they can be left out to simulate the doors being open.

I've also started a similar building that is a small bus garage/depot....but I've not printed it yet!

Looking good, will have to order some fire engines when its sorted. :D
Mike based on the Southern side of London

Posting most of the time from a mobile phone please excuse typos
Nutter
 
Posts: 330
Joined: Tue Feb 24, 2015 12:05 pm

Re: New products for the Talking T Gauge shop???

Postby dkightley » Sat Jul 22, 2017 11:13 am

Three new products just added to the shop.....

A rural fire station:
P1020025_red.JPG
P1020025_red.JPG (63.88 KiB) Viewed 279 times

The garage doors are removable so fire engines can be shown inside the station. The doors are also reversible so two different door styles can be shown....folding and up and over sectional.


A rural bus garage or depot:
P1020028_red.JPG
P1020028_red.JPG (65.6 KiB) Viewed 279 times

The garage doors are removable so buses can be seen inside!


An Art Deco style cinema:
P1020031_red.JPG
P1020031_red.JPG (69.96 KiB) Viewed 279 times

This cinema is based on a local cinema that has been recently re-opened after renovation following a long time sitting unused.


I am also working on a set of viaducts that are designed to match with the sectional track straight and curved sections. These are based on viaducts I have designed for a specific project for Jim Rusk (Ruskyviewer). More on these in the next day or so.......
Doug Kightley
Webmaster here and volunteer at the National Tramway Museum http://www.tramway.co.uk
User avatar
dkightley
 
Posts: 861
Joined: Wed Nov 13, 2013 9:43 pm
Location: Nottingham, UK

Re: New products for the Talking T Gauge shop???

Postby Nutter » Mon Jul 31, 2017 2:24 pm

Doug, could you please add a corner shop to the range. Same format as existing shops but with a shopfront on 2 sides to enable streets in built up areas to be at 90 degrees .like this -local to you :D
https://www.google.co.uk/maps/@52.92516 ... 6656?hl=en
Mike based on the Southern side of London

Posting most of the time from a mobile phone please excuse typos
Nutter
 
Posts: 330
Joined: Tue Feb 24, 2015 12:05 pm

Previous

Return to 3D Printing for T Gauge

Who is online

Users browsing this forum: No registered users and 1 guest


cron